Stainless Steel Flanged Fittings Manufacturer

Stainless Steel Flanged Pipe Fittings are often used in rigid piping conditions such as waste water treatment or filtration and industrial fluid process applications.

Flanged Stainless Steel Pipe Fittings Available in form of:

laterals elbows reducing tees 
concentric reducer eccentric reducer reducing crosses
true wyes  welded crosses  tees
spool pieces custom fittings  
Stainless Steel Flanged Pipe Fittings manufacturer

Stainless Steel Flanged Pipe Fittings manufacturer

Flange Details
ANSI/AWWA C110/A21.10, C111/A21.11 or C153/A21.53

The flanges shown are adequate for water service of 250 psi working pressure and should not be confused with class 250 flanges per ANSI B16.1. The bolt circle and the bolt holes match those of ANSI B16.1 class 125. If flanges are required to be made in accordance with other ratings or other standards, this must be specified on the purchase order. 24″ and smaller flanges are rated equal to the fittings to which they are attached and are adequate for water service of greater than 350 psi only with the use of gaskets.

We recommend that Vishal Steel gaskets be used for normal water service.

Facing: Stainless Steel Flanges are plain faced and are finished smooth or with shallow serrations

Back facing: Stainless Steel Flanges may be back faced or spot faced, for compliance with the flange thickness tolerance.

Drilling: Drilling of Stainless Steel flanges can be rotated when required; for those sizes with an even number of bolt holes in each quadrant, the fitting can be rotated 45° with standard drilling.

Stainless Steel Flanged Fittings Dimension

Size
(in.)
O.D.
(in.)
B.C.
(in.)
T
(in.)
Bolt Hole
Diameter
(in.)
Bolts
No. Per
Joint
Size
(in.)
3 7.50 6.00 0.75 3/4 4 5/8 × 2 1/2
4 9.00 7.50 0.94 3/4 8 5/8 × 3
6 11.00 9.50 1.00 7/8 8 3/4 × 3 1/2
8 13.50 11.75 1.12 7/8 8 3/4 × 3 1/2
10 16.00 14.25 1.19 1 12 7/8 × 4
12 19.00 17.00 1.25 1 12 7/8 × 4
14 21.00 18.75 1.38 1 1/8 12 1 × 4 1/2
16 23.50 21.25 1.44 1 1/8 16 1 × 4 1/2
18 25.00 22.75 1.56 1 1/4 16 1 1/8 × 5
20 27.50 25.00 1.69 1 1/4 20 1 1/8 × 5
24 32.00 29.50 1.88 1 3/8 20 1 1/4 × 5 1/2
30 38.75 36.00 2.12 1 3/8 28 1 1/4 × 6 1/2
36 46.00 42.75 2.38 1 5/8 32 1 1/2 × 7
42 53.00 49.50 2.62 1 5/8 36 1 1/2 × 7 1/2
48 59.50 56.00 2.75 1 5/8 44 1 1/2 × 8
54 66.25 62.75 3.00 2 44 1 3/4 × 8 1/2
60 73.00 69.25 3.12 2 52 1 3/4 × 9
642 80.00 76.00 3.38 2 52 1 3/4 × 9

1 The dimensions of 64″ stainless steel flange correspond with applicable dimensions of 66″ Class E in ANSI/AWWA C207, and 64″ ductile iron flanges can be connected to those flanges.

stainless steel Flanged Fitting Dimensions and Designation of Outlets
ANSI/AWWA C110/A21.10, C153/A21.53, or AMERICAN Standard

Stainless Steel Flanged Fittings Dimensions

See the table below for dimensions for the above fittings. Some of the above fittings are not listed in AWWA C110, but do meet applicable requirements of AWWA C110.

The largest opening establishes the basic size of a reducing fitting. The largest opening is named first, except for bull-head tees and for double-branch bends where both branches are reducing; in these two cases the largest opening is named last.

In the designation of the openings of stainless steel reducing fittings, they should be read in the order indicated by the sequence of the numbers 1, 2, 3 and 4 as shown.

In describing stainless steel tees reducing on the branch only, the first size applies to both outlets on the run. Similarly, for stainless steel crosses with the same size for both run outlets and the same size for both branch outlets, it is necessary to indicate only two sizes. For example: for an 8 × 6 tee or wye – it is not necessary to show 8 × 8 × 6; for an 8 × 6 cross – it is not necessary to show 8 × 8 × 6 x 6.

Size
(in.)
Dimensions1 in Inches Reducing Tees 
and Crosses
Reducing Wyes2
A B C D1 E1 F R S
(Dia.)
T U Size of Branches and Smaller4 H J Size of Branches and Smaller M N P
3 5.5 7.75 3.0 10.0 3.0 6 4.88 5.00 0.56 0.50 see5 see5 see6 see6 see6
4 6.5 9.00 4.0 12.0 3.0 7 5.50 6.00 0.62 0.50 see5 see5 see6 see6 see6
6 8.0 11.50 5.0 14.5 3.5 9 7.00 7.00 0.69 0.62 see5 see5 see6 see6 see6
8 9.0 14.00 5.5 17.5 4.5 11 8.38 9.00 0.94 0.88 see5 see5 see6 see6 see6
10 11.0 16.50 6.5 20.5 5.0 12 9.75 9.00 0.94 0.88 see5 see5 see6 see6 see6
12 12.0 19.00 7.5 24.5 5.5 14 11.25 11.00 1.00 1.00 see5 see5 see6 see6 see6
14 14.0 21.50 7.5 27.0 6.0 16 12.50 11.00 1.00 1.00 see5 see5 see6 see6 see6
16 15.0 24.00 8.0 30.0 6.5 18 13.75 11.00 1.00 1.00 see5 see5 see6 see6 see6
18 16.5 26.50 8.5 32.0 7.0 19 15.00 13.50 1.12 1.12 12 13 15.5 8 25.0 1.00 27.5
20 18.0 29.00 9.5 35.0 8.0 20 16.00 13.50 1.12 1.12 14 14 17.0 10 27.0 1.00 29.5
24 22.0 34.00 11.0 40.5 9.0 24 18.50 13.50 1.12 1.12 16 15 19.0 12 40.5 9.0 40.5
30 25.0 41.50 15.0 see3 see3 30 23.00 16.00 1.19 1.15 20 18 23.0 see3 see3 see3
36 28.0 49.00 18.0 see3 see3 36 26.00 19.00 1.25 1.15 24 20 26.0 see3 see3 see3
42 31.0 56.50 21.0 see3 see3 42 30.00 23.50 1.44 1.28 24 23 30.0 see3 see3 see3
48 34.0 64.00 24.0 see3 see3 48 34.00 25.00 1.56 1.42 30 26 34.0 see3 see3 see3
54 39.0 20.5 see7 38.00 27.50 1.69 1.55 see8 see8 see8
60 43.0 23.5 see7 42.00 32.00 1.88 1.75 see8 see8 see8
64 48.0 25.0 see7 44.00 38.75 2.12 1.75 see8 see8 see8

1 See flanged 90° bends for “K” dimensions.

2 AWWA C110 and C153 do not include data on wyes of any size.

3 Wyes are special. Substituting a pipe with a lateral welded-on outlet may be more economical and offer quicker shipment. A tee with a 45° bend may also offer quicker shipment.

4 For larger branches, use “A” dimensions.

5 For these smaller-diameter reducing tees and crosses, the “A” dimension applies as shown in “cut” of standard tee and cross.

6 For these smaller-diameter reducing wyes, the “D” and “E” dimensions apply as shown in “cut” of standard wye.

7 “F” dimensions for 54″-64″ reducers vary with diameters of reduction.

8 “H” and “J” dimensions for 54″-64″ tees and crosses vary with diameters of reduction.